서지주요정보
Aluminium 다결성에서 결정립의 결정방위가 피로변형에 미치는 영향 = On the relation between crystal orientation and fatigue deformation in Al-polycrystal
서명 / 저자 Aluminium 다결성에서 결정립의 결정방위가 피로변형에 미치는 영향 = On the relation between crystal orientation and fatigue deformation in Al-polycrystal / 허성강.
발행사항 [서울 : 한국과학기술원, 1977].
Online Access 원문보기 원문인쇄

소장정보

등록번호

4000375

소장위치/청구기호

학술문화관(문화관) 보존서고

MMS 7717

휴대폰 전송

도서상태

이용가능(대출불가)

사유안내

반납예정일

리뷰정보

초록정보

Distribution of slip bands in each grain of different orientation in the aluminium polycrystals has been studied after the specimens are fatigued with cyclic tensile stress. Purity of the studied aluminium is 99.9% and the grains of the samples are grown in the size of 1.5-3.0mm by heat treatment. Crystal orientation of each grain in the polycrystal has been determined by Laue back reflection method. Cyclic tensile load has been applied between two predetermined lower and higher stresses i.e. $σ_{max}$ and $σ_{min}$ values are 189 - 47$g/mm^2$ for specimen I and 198 - 32$g/mm^2$ for specimen II respectively. The distribution of slip bands has been observed under an optical microscope. Experimental results have shown that the slip bands have appeared predominantly at the grains whose crystal orientations lie to the direction which is the corresponding slip direction under the unidirectional tensile load. From this result one may say that slip also has occurred easily at the grains of large values of Schmid factor by cyclic fatigue load. As the Schmid factor value of one grain is decreasing, the number of cycles inducing the first observable slip band in that grain in increased. At the grains of lower values of Schmid factor, for example, 0.371 and 0.337, no observalble slip band is appeared up to 10,000 cycles of fatigue.

Aluminium 다결정을 반복인장으로 피로시켜, 결정립면상에 형성된 slip band의 분포상태를 조사하여 다결정을 구성하고 있는 각 결정립의 방위와 각 결정립에 형성된 slip band의 분포사이의 관계를 조사하였다. 사용한 Aluminium의 순도는 99.9% 였으며 결정립은 크기가 1.5~3.0mm가 되도록 성장시켰고 다결정의 각 결정립의 방위는 Laue back reflection방법으로 결정하였다. 피로응력은 $σ_{max}$ 와 $σ_{min}$의 값이 시편 I의 경우 189와 47$g/mm^2$, 시편II의 경우 198과 32 $g/mm^2$을 유지하면서 70cpm의 frequeney로 반복인장시켰고, slip band의 분포는 광학현미경으로 관찰하였다. 실험결과 Aluminium 다결정에 반복 인장력을 가할 경우, 결정립의 방위가 slip이 일어나기 쉽도록 놓여진 결정립 즉 결정립의 인장 방향에 대한 Schmid계수가 큰 결정립에서 slip이 우선적으로 일어나는 것을 알았다. 즉 다결정을 구성하고 있는 결정립의 Schmid 계수가 작은 것일 수록 처음 광학현미경으로 관측될 수 있는 slip band가 나타나는데 요하는 반복응력의 회수가 증가하며 극단적으로 Schmid계수가 아주 작은 결정립 (Schmid계수 ; 0.337, 0.371) 에서는 반복응력의 회수를 1,000번 또는 10,000번으로 증가시켜도 slip band가 나타나지 않았다.

서지기타정보

서지기타정보
청구기호 {MMS 7717
형태사항 ii, 34 p. : 삽화 ; 26 cm
언어 한국어
일반주기 저자명의 영문표기 : Sung-Kang Hur
지도교수의 한글표기 : 남수우
지도교수의 영문표기 : Soo-Woo Nam
학위논문 학위논문(석사) - 한국과학기술원 : 재료공학과,
서지주기 참고문헌 : p. 27-32
주제 Aluminum alloys.
Fatigue.
Orientation.
Metals --Mechanical properties.
Deformations (Mechanics)
알루미늄 합금. --과학기술용어시소러스
피로. --과학기술용어시소러스
기계적 성질. --과학기술용어시소러스
방향 (방위) --과학기술용어시소러스
소성 변형. --과학기술용어시소러스
QR CODE

책소개

전체보기

목차

전체보기

이 주제의 인기대출도서