The characteristics of dynamic strain-ageing behavior have been observed in the quenched and tempered state of ASME SA508 class3 nuclear pressure vessel steel. Serrated flow has been observed in the temperature range 180-340℃ with nominal strain rates varying from $2.08\times10^{-4}/s$ to $1.25\times10^{-3}/s$. It has been noted that dynamic strain-ageing causes a sharp rise in ultimate strength and marked decrease in ductility and a negative strain-rate sensitivity of the flow stress. The region of dynamic strain-aging at higher strain rate is shift to higher temperature than that of low strain rate. The temperature and strain-rate dependence of the onset of serrations yields an activation energy of 68KJ/mol(16.2Kcal/mol) which suggests that the process is controlled by interstitial diffusion, probably of carbon and nitrogen in ferrite. Using direct current potential drop(DCPD)method, $J_i$ value that is true crack initiation, has been affected by dynamic strain-ageing effect. Therefore, the drop in $J_i$ at elevated temperature is due to the interaction of the interstitial impurities with dislocations at the crack front. On the other hand, comparing $J_{IC}$ as measured from ASTM E813, the $J_i$ from DCPD is more sensitive to detect the crack initiation. After crack initiation, the crack propagation was also affected by dynamic strain-ageing effect from the analysis of tearing modulus. The tearing modulus of the serrated region is about 30% smaller than that of room temperature. From the SEM work of fracture surface, cleavage shapes have been obtained in the minimum toughness range that is affected by DSA.
켄칭과 템퍼상태의 ASME SA508 class3원자로 압력용기강에서 동적변형시효의 특징을 관찰할 수 있다. 인장실험에 의해 변형속도를 $2.08\times10^{-4}/s$에서$1.25\times10^{-3}/s$로 변화함에 따라 톱니모양의 영역에서 극한강도가 증가하고, 연성이 상당히 감소하며, 유동응력의 변형속도 감도가 음의 값을 가졌다. 또한, 높은 변형속도에서의 동적변형시효 영역은 낮은 변형속도에서 보다 더 높은 온도영역으로 이동했다. 톱니모양 응력이 시작되는 온도와 변형속도로부터 계산된 활성화에너지는 68KJ/mol(16.22Kcal/mol)이었고 이 값은 페라이트내에서 탄소와 질소의 확산에 필요한 활성화에너지와 일치된다.
한편, 파괴실험에서는 진균열발생을 잘 표현하는 J 값을 구하기위해 계산된 $J_i$값은 동적변형시효 영역에서 떨어지게 되는데 이것은 균열선단에서 전위와 불순물과의 작용 때문이다. 그러므로 $J_i$값은 동적변형시효 효과에 의해 영향을 받는다는 것을 알 수 있다. 반면 ASTM E813에 의한 $J_{IC}$ 값은 동적변형시효 효과에 영향없이 거의 일정했다. 균열발생이후 균열전파는 찢어짐계수 T로 해석을 했는데, 이 값 역시 동적변형시효 영역에서 상온보다 30%가량 낮은 값을 가졌다. 그러므로 동적변형시효가 균열전파에 큰 영향을 줌을 알 수 있었고 주사전자현미경을 이용한 파면관찰에서도 최소 취성을 갖는 동적변형시효 영역에서 벽계파괴를 볼 수 있었다.